Albums, sticky photos and repairs to prints
Every album type, every removal method people use with its real risk, how to deal with sticky backs and residue, photos stuck to each other, curled prints, and when not to remove anything.
๐งฐ What you'll need
Every tool and supply named in this unit. Dotted-underlined words in the text jump back here. Buttons open that store's search for the exact product. Prices are rough ranges in Canadian dollars.
Nitrile gloves, powder-free under $25
What it is: Thin disposable rubber-like gloves. They keep skin oil off film and glossy photos and still let you grip.
Our pick: Any powder-free nitrile exam gloves, in your size (S, M, L). Not latex, not vinyl.
In a store: Pharmacy, Costco, hardware store
Rocket blower under $25
What it is: A rubber bulb you squeeze. It puffs clean dry air to push dust off without touching.
Our pick: Giottos Rocket Air Blaster, large
In a store: Camera store
Anti-static brush $25 to $100
What it is: A very soft brush whose fibres remove static, so dust lets go of film and prints.
Our pick: Kinetronics StaticWisk, 2 inch or 4 inch
In a store: Camera store
Support card (support board) under $25
What it is: A stiff, clean, flat piece of card, a little bigger than the photo. You slide it under a photo and then carry the card, so the photo never bends or hangs from your fingers.
Our pick: Cut your own from 4-ply acid-free mat board (Crescent or Lineco). Cut several sizes: 5x7, 8x10, 11x14 inch. For practice, a new file folder works.
In a store: Michaels or any framing shop sells mat board and will cut it. Carr McLean sells archival board.
Painter's tape under $25
What it is: Low-tack paper tape that peels off cleanly. For labelling containers and holding cracked glass together. Never on a photo, film or tape surface.
Our pick: ScotchBlue Original painter's tape, 24 mm
In a store: Hardware store
Polyester (Mylar) sleeves $25 to $100
What it is: A crystal-clear, chemically safe plastic pocket, open on two sides. A tacky or flaking photo goes inside so it can be scanned and stored without touching anything.
Our pick: Archival polyester L-sleeves (sold as Mylar or Melinex), 5x7 and 8.5x11 inch
In a store: Carr McLean
Micro spatula under $25
What it is: A thin, flat, stainless steel blade with rounded ends, about 18 cm long. It slides under photos, backing boards and tape without cutting.
Our pick: Stainless steel double-ended micro spatula (lab type), one flat rounded end
In a store: Carr McLean, lab supply
Unwaxed dental floss under $25
What it is: Plain thread for cleaning teeth. Slid under a photo and worked side to side, it cuts album glue. Must say UNWAXED and have no flavour.
Our pick: Any unwaxed, unflavoured floss. Read the box: most floss is waxed.
In a store: Pharmacy
Rubber cement pickup (crepe square) under $25
What it is: A small square of soft natural crepe rubber. Rubbed lightly over sticky glue, it grabs the glue and rolls it into crumbs that brush away. Dry. No chemicals.
Our pick: Best-Test Pik-Up rubber cement eraser. Buy several: they get dirty.
In a store: Art store, Michaels, framing shop
Adhesive remover (un-du) under $25
What it is: A fast-evaporating solvent that releases sticky glue for a few seconds. Supervisor only, back of the photo only.
Our pick: un-du Adhesive Remover, with its built-in scraper
In a store: Craft store, scrapbooking aisle
Blotter paper $25 to $100
What it is: Thick, soft, absorbent, acid-free paper. Wet or humidified photos dry between or on top of it.
Our pick: Archival blotting paper sheets
In a store: Carr McLean, art store (watercolour blotter)
Silicone release paper under $25
What it is: Paper with a slippery coating that nothing sticks to. A tacky photo can rest on it.
Our pick: Archival silicone release paper
In a store: Carr McLean
Plastic tub with lid under $25
What it is: A large clear storage tub. With a tray of water and a rack inside, it becomes a humidity chamber for relaxing curled prints.
Our pick: Sterilite or Rubbermaid tub, about 60 L, with a cooling rack or plastic grid to hold items above the water
In a store: Hardware store, Walmart
Black backing paper under $25
What it is: Plain matte black paper, card or cloth. Stops show-through behind thin pages and blocks stray light around film and frames.
Our pick: Black cardstock and one sheet of black foam board
In a store: Michaels, dollar store
Hair dryer with a low setting $25 to $100
What it is: An ordinary hair dryer. Only its LOW heat setting is used, briefly, from behind an album page.
Our pick: Any hair dryer with a low or cool setting
In a store: Pharmacy
Small zip bags under $25
What it is: Clear resealable bags for screws, brads, cut film pieces and old parts. Job number written on the bag.
Our pick: Zip bags in snack and sandwich sizes
In a store: Grocery store
Copy stand $100 to $500
What it is: A flat base with a vertical post that holds a camera pointing straight down, steady and square.
Our pick: Kaiser RS 2 XA, or a budget tabletop copy stand from Neewer or JJC
In a store: Camera store
Pair of LED lights $100 to $500
What it is: Two matching lights on stands, one each side at 45 degrees, for photographing frames, albums and art.
Our pick: Two Neewer 660 LED panels (CRI 95+) with stands
In a store: Camera store
Remote shutter release under $25
What it is: A button on a cable or wireless that fires the camera so your hand does not shake it.
Our pick: The remote made for your camera model, or the camera's phone app
In a store: Camera store
Drying screens under $25
What it is: Clean fibreglass window screens laid flat on blocks, so air reaches both sides of wet photos.
Our pick: Fibreglass window screen in a frame, or a roll of screen mesh over a wooden frame
In a store: Hardware store
Before you remove a single photo
- 1Photograph every page
Whole page, straight on. This records order, layout and captions.
- 2Number the pages
A slip of paper with the page number in each photo, not written on the album.
- 3Read the job sheet
Did the client ask for photos to be removed, or scanned in place?
- 4Test one unimportant photo first
Bottom corner of a back page.
Know the album type
| Album type | Years | How photos are held | Default action |
|---|---|---|---|
| Magnetic or "sticky" album | 1960s to 1990s | Card page with lines of glue, clear plastic sheet over the top | Remove carefully if they release. These albums damage photos over time. |
| Pocket or slip-in album | 1980s on | Photos slide into clear pockets | Slide out. Check for sticking to the plastic. |
| Black or cream paper album with photo corners | 1900s to 1960s | Paper corners glued to the page, photo tucked in | Slide out of the corners |
| Black paper album, photos glued down | 1900s to 1960s | Paste or rubber cement under the whole photo | Do not remove. Scan the page. |
| Scrapbook | Any | Tape, glue, staples, mixed items | Do not remove. Scan the page. |
| Flip or flap album | 1960s on | Photos in overlapping hinged sleeves | Slide out one at a time, keep order |
| Victorian card album | 1860s to 1900s | Thick pages with slots for cabinet cards | Supervisor. Pages tear easily. |
| Self-adhesive "dry mount" album | 1990s on | Whole page is sticky | Treat as magnetic |
Removal methods, rated
| Method | Best for | How it works | Risk |
|---|---|---|---|
| Scan in place | Everything | Photo never leaves the page | None |
| Lift by hand, flat | Photos that are barely held | Lift a corner with the spatula and support it flat as it releases | Low |
| Dental floss | Magnetic albums, glued prints | Unwaxed floss is slid under and worked side to side to cut the glue | Low to medium |
| Micro spatula | Magnetic albums | Thin flat blade slides under, kept flat against the page | Low to medium |
| Polyester (Mylar) strip | Magnetic albums | A strip of thin stiff plastic film pushed under like a card | Low |
| Cool hair dryer on the page back | Stubborn magnetic glue | 10 to 15 seconds of low heat from behind the page softens the glue | Medium. Heat can soften the emulsion too. |
| Freezer | Stubborn magnetic glue | Page is bagged and frozen 5 to 10 minutes so the glue turns brittle | Medium. Condensation when it comes out. |
| Adhesive remover (un-du or similar) | Stubborn glue, supervisor only | A few drops under the edge release the glue, then evaporate | Medium. Never on inkjet prints or on the image side. |
| Cut the page | Photo will not release, client approves | Cut the album page around the photo and scan photo plus backing | Low for the photo. Destroys the page. |
| Pulling or bending the photo up | Nothing | Not a method | โ Never. Cracks the emulsion. |
| Kitchen knife, water, steam | Nothing | Seen online | โ Never |
The dental floss method
- 1Peel back the plastic cover sheet
Slowly. If a photo lifts with the plastic, stop and release the photo from the plastic first.
- 2Cut 40 cm of unwaxed dental floss
Unwaxed: wax leaves residue. Not flavoured.
- 3
- 4Slide the floss under the corner
- 5Hold the floss tight and low
Hands close to the page surface.
- 6Saw gently side to side while moving forward
The floss does the work. The photo stays flat.
- 7Stop if it catches
Come in from a different corner.
- 8Lift the freed photo onto a support card
The spatula and Mylar methods
- 1Start at a corner that is already slightly lifted
- 2Keep the blade flat on the page
The blade pushes against the page, not up into the photo.
- 3Short pushes, 5 mm at a time
- 4Follow with your other hand
Support the freed part so it does not flex.
Heat and cold, supervisor present
- 1Heat
Hair dryer on low, 20 cm away, aimed at the back of the page for 10 to 15 seconds. Test with floss. Repeat once at most.
- 2Cold
Page in a zip bag, air squeezed out, flat in a freezer 5 to 10 minutes. Work immediately while cold. Let the page reach room temperature inside the bag before opening, so water does not condense on the photos.
Sticky backs and residue
| What you find | What to do |
|---|---|
| Dry, non-tacky glue lines on the back | Leave them. They do no harm now. |
| Tacky back, one or a few photos | Do not stack. Put the photo in its own polyester sleeve, or lay it on silicone release paper. Scan through the sleeve. |
| Tacky backs, many photos | Use the Porthos volume method in the next section |
| Album paper stuck to the back | Leave it on. Scan as is. |
| Tape on the back | Leave it. Never peel. |
| Tape or glue on the front | Leave it. Fix digitally. Tell the supervisor. |
| Residue that must go (photo is being re-housed) | Supervisor only: adhesive remover on a cotton swab, back side only, tiny amount, ventilated room |
โ Do
- Protect the ET-2750 glass with a clear sleeve under any tacky print
- Clean the scanner glass after every tacky item
โ Do not
- Use Goo Gone, nail polish remover, rubbing alcohol or water on a photo
- Dust a tacky back with talc or flour. It ends up on the scanner glass and on other photos.
- Put a tacky print through the FastFoto
Sticky backs at volume: the Porthos method
Many album photos have a little tacky glue left on the back. It is enough to jam the FastFoto. This is how we handle hundreds or thousands of them.
Two rules first
- Keep tacky photos in a single layer, back side up, on silicone release paper, until they are cleaned.
- Keep them in order. Number the release paper sheets: sheet 1, sheet 2.
Step 1: touch test and sort
- 1
- 2Touch the back lightly with the back of one gloved finger
In the middle and along the old glue lines.
- 3Nothing grabs: "clean" pile. Normal FastFoto batch (Unit 5).
- 4It grabs or feels rubbery: "tacky" row on release paper, back side up.
- 5Paper from the album is stuck to the back, or the back is torn: flatbed pile. Do not try to clean it.
Step 2: lift the glue off, dry
Tool: a rubber cement pickup square. It is dry crepe rubber. It grabs glue and rolls it into crumbs.
- 1Test first on 10 unimportant prints from the same album
Different albums used different glue. Check that the glue lifts and the paper back is not roughened.
- 2Lay the photo face down on a clean support card
The card stops the photo flexing. Put a sheet of clean paper under the face.
- 3Hold the photo flat with two fingers of one hand, near the area you are cleaning
- 4Rub the pickup square over the glue with light, short strokes in one direction
Light pressure. Let the rubber grab the glue. Do not scrub.
- 5Glue rolls into small crumbs. Brush them off the edge with the soft brush, away from other photos.
- 6Touch test again
Not tacky: done. Still tacky after 3 passes: stop and move it to the "stubborn" row.
- 7Trim or change the pickup square when its surface is coated
Cut the dirty face off with scissors.
- 8Blow off the back and the front with the blower
โ Do
โ Do not
- Use the pickup square on the picture side
- Use it on inkjet prints, very thin paper, or backs with handwriting in pencil over the glue. It can lift the writing. Photograph the writing first.
- Press hard. A crease is permanent. A little glue left behind is not.
Step 3: stubborn glue, supervisor
- 1
- 2Photo face down on the support card
- 3One or two drops on the glue line only, on the back
- 4Wait 3 to 5 seconds, then lift the softened glue with the un-du scraper or the micro spatula held flat
- 5Let it evaporate fully: 30 seconds. Touch test.
- 6Never on inkjet prints. Never near the picture side.
Step 4: scan
| After cleaning the back is... | Scan it on |
|---|---|
| Clean and dry, photo in good condition | FastFoto, normal stacks. Clean the glass strips and rollers every 100 prints for these batches, not every 300. |
| Still slightly tacky | Camera copy station, or ET-2750 flatbed. Not the FastFoto. |
| Paper stuck on, torn, fragile | ET-2750 flatbed, as is |
Camera copy station for tacky photos (fastest)
- 1Copy stand, camera pointing straight down, two lights at 45 degrees (Unit 6)
- 2A sheet of silicone release paper on the base, with a corner guide made from two strips of painter's tape
Every photo goes into the same corner.
- 3Photo back down on the release paper. Nothing touches the picture.
- 4Shoot with the remote. Lift the photo by its edges. Next.
- 5About 2 to 3 seconds per photo once the rhythm is set
- 6Check focus every 50 photos. Replace the release paper when glue builds up on it.
ET-2750 flatbed for tacky photos (no new equipment)
- 1Four photos face down on the glass, 20 mm apart
- 2Lay one sheet of silicone release paper over their backs
This stops the tacky backs gluing themselves to the scanner lid.
- 3Lower the lid gently. Scan in Photo Mode at 600 dpi (Unit 5).
- 4Lift the release paper, then the photos, straight up
- 5Wipe the glass after every tacky batch
| If you see or hear | Likely cause | Do this |
|---|---|---|
| FastFoto double-feeds or stops on "cleaned" photos | Glue still on some backs | Touch test them again. Pull the tacky ones. |
| Streak appears partway through a batch | Glue reached a glass strip | Stop. Clean strips and rollers. Rescan from where the streak began. Find the photo that caused it. |
| Back looks fuzzy or rough after the pickup square | Paper fibres lifting: too much pressure, or weak paper | Stop using it on that album. Camera or flatbed. |
| Crumbs on the picture side | Brushed toward the photo | Blower only. Do not wipe. |
| Glue smears instead of rolling up | Glue is soft and oily | Stubborn row. un-du, supervisor. |
Photos stuck to each other
A stack that got damp becomes a brick. The gelatin of one photo has bonded to the back of the next.
- 1Do not pry them apart dry
The image will split between the two.
- 2Scan what is visible first
The top photo and the bottom back.
- 3Tell a supervisor
The next step needs client consent.
- 4Water release, supervisor only
Traditional black and white and colour photo-lab prints can often be released by soaking in clean room-temperature water for 15 to 30 minutes until they slide apart on their own.
- 5Dry face up
On a clean screen or blotter, not touching each other. Never use heat.
- 6Flatten after drying
See below.
Curled and rolled prints
| Problem | Safe fix |
|---|---|
| Slight curl | Scan on the flatbed with a sheet of white paper and a light book on top |
| Print rolled into a tube, feels flexible | Supervisor: humidify, then press. Steps below. |
| Brittle, cracks when you try to open it | Do not unroll. Supervisor. Photograph as is. |
| Fiber-based print curled toward the image | Humidify and press |
Humidify and press, supervisor present
- 1Build a humidity chamber
A large plastic tub with a lid. A tray of room-temperature water in the bottom. A rack or screen above the water.
- 2Put the print on the rack
It must not touch the water.
- 3Close the lid and wait 2 to 6 hours
Check hourly. The print relaxes and can be opened without resistance.
- 4Lay it between two sheets of clean blotter paper
- 5Put a flat board and a weight on top
A few heavy books.
- 6Leave 2 to 5 days, changing blotters after the first day
โ Do
โ Do not
- Iron a photo
- Back-roll a brittle print
- Leave a print in the humidity chamber overnight. Mold starts in about 48 hours of damp.
Scanning album pages in place
- 1Open the album flat only as far as it wants to go
Never force the spine.
- 2Page fits the ET-2750 and lies flat
Scan the whole page at 600 dpi, then each photo is cropped from the page scan.
- 3Page is bigger than the glass
Scan in overlapping sections, then stitch (Unit 17), or photograph it.
- 4Page will not lie flat, or album is thick
Photograph on the copy stand with two lights at 45 degrees (Unit 6).
- 5Leave the plastic cover sheet off for the scan if it peels back easily
It causes glare. Lay it back afterward.
- 6Capture captions
Every page scan must include the handwriting. It is often the only record of names.
2611_ALB1_p07_c.tif.
โถAn archivist removes photos from an adhesive album๐ Watch for: the floss staying low and the photo staying flatOpens on YouTube in a new tab
โถ4 ways out of sticky albums: spatula, polyester film, floss, hair dryer๐ Watch for: each tool in useOpens on YouTube in a new tab
โถRemoving photos from sticky albums without damage๐ Watch for: how little force is usedOpens on YouTube in a new tab
โถFour tools for adhesive-back albums๐ Watch for: the tools side by sideOpens on YouTube in a new tab
โถRemoving a stuck photo, part 1๐ Watch for: where the first corner is liftedOpens on YouTube in a new tab
โถRemoving a stuck photo, part 2: freezing๐ Watch for: bagging the page before the freezerOpens on YouTube in a new tab
โถFlattening curled photos๐ Watch for: the humidity chamber set-upOpens on YouTube in a new tab
โถHumidification for a folded corner๐ Watch for: how slowly the paper is openedOpens on YouTube in a new tab
โถA homemade humidity chamber๐ Watch for: the rack that keeps items above the waterOpens on YouTube in a new tab
โถSaving flood-damaged photos that are stuck together๐ Watch for: prints separating in water on their ownOpens on YouTube in a new tab
โถSalvaging water-damaged photographs๐ Watch for: drying face upOpens on YouTube in a new tab๐ Worksheet 7: Albums, sticky photos and repairs to prints
Part A: Quick check
Click one answer. Green means correct. Red means try again. You can try as many times as you need.
1. What is the Porthos default for photos in an album?
โ The photo never leaves the page, so there is no risk, and captions are captured too.
2. Which floss do we use?
โ Wax and flavour leave residue on the back of the photo.
3. Where is the hair dryer aimed?
โ Heat from behind softens the glue with the least effect on the image layer.
4. A black paper album has photos pasted flat to the page. What do we do?
โ Pasted photos tear before the paste releases.
5. A photo has a tacky back. Which scanner and how?
โ Tacky glue would coat the FastFoto rollers and the flatbed glass.
6. Can we dust a sticky photo back with cornstarch or baby powder so it feeds through the FastFoto?
โ The powder itself becomes the residue, in the scanner and on the original.
7. Why are tacky photos never stacked?
โ A tacky back pressed on a photo face leaves glue on the image.
8. What tool lifts tacky glue off the back, dry?
โ Crepe rubber grabs the glue and rolls it into crumbs.
9. After freezing an album page, when is the bag opened?
โ Opening a cold bag lets water condense on the photos.
10. Two photos are stuck face to back. What do you do?
โ Dry separation splits the image layer.
11. A rolled print cracks when you start to open it. What do you do?
โ Brittle prints break. They are photographed as they are or humidified by a supervisor.
Part B: Hands-on practice
Do each task with real equipment and practice media. Tick it when you have done it. Your trainer signs when they have watched you do it.
| I did it | Task | Trainer initials |
|---|---|---|
| Photograph and number every page of a practice album. | ||
| Remove 5 photos from a magnetic practice album with floss with no new creases. | ||
| Remove 3 photos with the micro spatula. | ||
| Decide "remove" or "scan in place" for 6 practice album pages and explain why. | ||
| Scan a tacky-backed practice print through a polyester sleeve and clean the glass afterward. | ||
| Touch-test and sort 30 practice prints into clean, tacky and flatbed groups. | ||
| Clean the backs of 10 tacky practice prints with the pickup square, with no creases and no crumbs left. | ||
| Scan 4 tacky prints on the ET-2750 with release paper over their backs. | ||
| Scan an album page in place and crop the individual photos with correct names. | ||
| Build a humidity chamber and flatten a curled practice print. |
Part C: Write or draw your answer
1. List the removal methods from lowest risk to highest risk.
2. Name 4 kinds of photo that must never be soaked in water.