Framed photos
How to open a frame safely, every method people use to get a photo out, what to do when the photo is stuck to the glass, and how to capture it without removing it at all.
๐งฐ What you'll need
Every tool and supply named in this unit. Dotted-underlined words in the text jump back here. Buttons open that store's search for the exact product. Prices are rough ranges in Canadian dollars.
Support card (support board) under $25
What it is: A stiff, clean, flat piece of card, a little bigger than the photo. You slide it under a photo and then carry the card, so the photo never bends or hangs from your fingers.
Our pick: Cut your own from 4-ply acid-free mat board (Crescent or Lineco). Cut several sizes: 5x7, 8x10, 11x14 inch. For practice, a new file folder works.
In a store: Michaels or any framing shop sells mat board and will cut it. Carr McLean sells archival board.
Painter's tape under $25
What it is: Low-tack paper tape that peels off cleanly. For labelling containers and holding cracked glass together. Never on a photo, film or tape surface.
Our pick: ScotchBlue Original painter's tape, 24 mm
In a store: Hardware store
Micro spatula under $25
What it is: A thin, flat, stainless steel blade with rounded ends, about 18 cm long. It slides under photos, backing boards and tape without cutting.
Our pick: Stainless steel double-ended micro spatula (lab type), one flat rounded end
In a store: Carr McLean, lab supply
Unwaxed dental floss under $25
What it is: Plain thread for cleaning teeth. Slid under a photo and worked side to side, it cuts album glue. Must say UNWAXED and have no flavour.
Our pick: Any unwaxed, unflavoured floss. Read the box: most floss is waxed.
In a store: Pharmacy
Black backing paper under $25
What it is: Plain matte black paper, card or cloth. Stops show-through behind thin pages and blocks stray light around film and frames.
Our pick: Black cardstock and one sheet of black foam board
In a store: Michaels, dollar store
Hair dryer with a low setting $25 to $100
What it is: An ordinary hair dryer. Only its LOW heat setting is used, briefly, from behind an album page.
Our pick: Any hair dryer with a low or cool setting
In a store: Pharmacy
Needle-nose pliers under $25
What it is: Pliers with long thin jaws, for pulling small nails, brads and staples straight out of a frame.
Our pick: Any 6 inch needle-nose pliers
In a store: Hardware store
Small flat screwdriver or putty knife under $25
What it is: A thin flat blade for bending up frame tabs and lifting points.
Our pick: Precision screwdriver set, plus a 1 inch flexible putty knife
In a store: Hardware store
Utility knife under $25
What it is: A retractable knife with snap-off blades, for slitting the paper dust cover of a frame. Always a fresh blade.
Our pick: Olfa 9 mm snap-off knife
In a store: Hardware store
Cut-resistant gloves under $25
What it is: Thick woven gloves that a glass edge cannot slice through. For cracked or broken frame glass.
Our pick: Cut level A4 or higher (NoCry or similar)
In a store: Hardware store, safety supply
Safety glasses under $25
What it is: Clear impact-rated glasses for work with broken glass, soot and mold.
Our pick: Any CSA-rated safety glasses
In a store: Hardware store
Padded surface (towel or foam) under $25
What it is: A soft layer on the table so frame fronts and glass are not scratched or cracked.
Our pick: A clean bath towel, or a 1 cm closed-cell foam sheet
In a store: Already in the building, or a fabric store
Small zip bags under $25
What it is: Clear resealable bags for screws, brads, cut film pieces and old parts. Job number written on the bag.
Our pick: Zip bags in snack and sandwich sizes
In a store: Grocery store
Copy stand $100 to $500
What it is: A flat base with a vertical post that holds a camera pointing straight down, steady and square.
Our pick: Kaiser RS 2 XA, or a budget tabletop copy stand from Neewer or JJC
In a store: Camera store
Pair of LED lights $100 to $500
What it is: Two matching lights on stands, one each side at 45 degrees, for photographing frames, albums and art.
Our pick: Two Neewer 660 LED panels (CRI 95+) with stands
In a store: Camera store
Polarizing filter and film $25 to $100
What it is: A filter that screws on the lens, and plastic sheets that go over the lights. Together they remove glare from glass and glossy photos.
Our pick: Circular polarizer (Hoya or K&F Concept) in your lens thread size, plus linear polarizing film sheets
In a store: Camera store
Grey card or colour target $25 to $100
What it is: A card of exact neutral grey, or a chart of known colours. Photographed once per set-up so colour can be corrected precisely.
Our pick: Calibrite ColorChecker Passport Photo 2. Budget: any 18% grey card.
In a store: Camera store
Remote shutter release under $25
What it is: A button on a cable or wireless that fires the camera so your hand does not shake it.
Our pick: The remote made for your camera model, or the camera's phone app
In a store: Camera store
Small flat mirror under $25
What it is: A pocket mirror laid flat under the camera. When the lens sees itself in the exact centre, the camera is square.
Our pick: Any flat pocket mirror, about 5 to 8 cm
In a store: Dollar store, pharmacy
The decision comes first
The safest way to digitize a framed photo is often to leave it in the frame.
| Situation | What we do |
|---|---|
| Photo is loose inside the frame and the client agrees to opening | Open the frame, scan on the flatbed, put it back |
| Photo is stuck to the glass | Do not separate. Capture through the glass. |
| Frame is sealed, valuable, antique, or professionally framed with a paper dust cover | Ask the client first. Opening changes the object. |
| Oval or bubble (convex) glass portrait | Supervisor only. The print underneath is often curved and cracks if flattened. |
| Cased image (daguerreotype, ambrotype, tintype in a hinged case) | Never open. Photograph through its own glass. |
| Client said "do not open" | Capture through the glass |
Layers of a frame
Tools
Opening a frame, step by step
- 1Photograph front and back
Include any labels, framer's stickers and writing on the back.
- 2Check the glass
Cracked? Put on cut-resistant gloves and glasses. Tape across the crack with painter's tape on the outside so pieces stay together.
- 3Lay the frame face down on the towel
- 4Remove hanging wire if it is in the way
Bag the hardware.
- 5Dust cover
If there is brown paper sealing the back, slit it neatly along the inside edge of the frame on three sides and fold it back like a door. Keep any labels.
- 6Find what holds the backing in
Flexible tabs: bend them up. Swivel clips: turn them. Brads, glazier's points or staples: pull each one straight out with pliers.
- 7Lift the backing board
Slide the spatula under one edge. If it resists, look for a fastener you missed.
- 8STOP and look
Is the photo attached to the backing? Is it attached to the mat? Is it touching the glass?
- 9Test for sticking
Lift one corner of the photo by about 2 mm with the spatula. If the surface pulls or you see it clinging to the glass, stop. Go to "Stuck to the glass".
- 10Lift the photo out
Support it from underneath with a sheet of card. Do not peel it by a corner.
- 11Photograph the inside
Notes, dates and old newspaper are often hidden behind photos. Scan them too.
Ways photos are fixed inside frames
| How it is attached | How to release it | Risk |
|---|---|---|
| Loose, held only by pressure | Lift out | Low |
| Paper hinges or tape at the top edge to the mat | Leave the hinges on the photo. Cut the hinge between photo and mat with a blade laid flat. | Low |
| Photo corners | Slide the photo out of the corners | Low |
| Masking tape or clear tape on the back edges | Leave the tape on. Cut the tape at the edge of the photo. Never peel tape off a photo. | Medium |
| Dry mounted or glued down to the backing | Do not separate. Scan the photo on its board. | High if you try |
| Glued to the mat window | Do not separate. Scan with the mat, or through the mat opening. | High if you try |
| Stuck to the glass | See next section | Very high |
Stuck to the glass
Moisture softens the gelatin surface of a photo. It then bonds to the glass like glue. This is common in bathrooms, kitchens, basements and after floods.
Every method people use, rated
| Method | What it is | Our rating |
|---|---|---|
| Leave it and capture through the glass | Scan or photograph the photo with the glass still attached | โ Always do this first. Zero risk. |
| Send to a photograph conservator | A trained professional separates it under controlled conditions | โ The only safe way to physically separate a valuable photo |
| Room-temperature water soak | Glass and photo are submerged in clean water until the gelatin releases, then dried face up | โ ๏ธ Supervisor only, only with written client consent, only after a through-glass capture exists. Can destroy inkjet prints, old colour prints and hand colouring. |
| Freezer | Frame is frozen in the hope that the bond turns brittle | โ Unreliable. Condensation on thawing can make it worse. |
| Hair dryer on the back of the glass | Warming to soften the bond | โ Heat makes gelatin stickier and can crack glass |
| Steam or a clothes iron | Heat and moisture through a towel | โ Never. Seen in online videos. Destroys emulsion. |
| Sliding a blade or floss between photo and glass | Cutting the bond | โ Never. Scrapes the image off. |
Capturing through the glass
- 1Take the glass and photo out together
Remove the frame moulding and backing so the glass can lie flat. If they will not come out safely, leave everything assembled and use the camera method.
- 2Clean the outside of the glass
Glass cleaner on the cloth, not sprayed on the frame. Liquid must not reach the edge of the photo.
- 3Try the ET-2750 flatbed
Glass side down. Scan at 600 dpi and zoom to 100%.
- 4Judge sharpness at 100% zoom
The ET-2750 focuses at its own glass surface. Through 2 mm of frame glass the photo is usually soft. If the eyes and hair are not crisp, use the camera method.
- 5Camera method
Photograph it on the copy stand (below).
- 6Bag any broken glass around the stuck area
Do not pick glass off the photo.
Photographing framed photos (no glare)
Use this for stuck photos, sealed frames, bubble glass, large frames and cased images.
- 1Stand the frame upright or lay it flat
Camera lens aimed at the exact centre, sensor parallel to the glass. A small mirror laid on the glass helps: when the lens sees itself in the centre, it is square.
- 2Two lights, one each side, at 45 degrees
Same distance, same height. Light at 45 degrees bounces away from the lens.
- 3Kill room reflections
Lights off in the room. Wear dark clothing. Hang black cloth or card behind the camera with a hole for the lens.
- 4Camera settings
Lowest ISO, aperture f/8, 2 second timer or remote, RAW if available, focus on the photo and not on the glass.
- 5Polarizer if we have one
A polarizing filter on the lens, rotated until the glare fades. Best result: polarizing film on both lights plus the lens filter (cross polarization).
- 6Shoot, zoom in, check
Look for your own reflection, light hot spots and soft focus.
- 7
Putting it back
- 1Clean the inside of the glass and let it dry completely
Damp glass is how photos stick.
- 2Layers back in the photographed order
- 3Refit the same fasteners
Push brads back in their holes with the side of the pliers. Never hammer over a photo.
- 4Tape the dust cover flap closed
Painter's tape on the paper only.
- 5Rehang hardware as it was
โถA picture framer removes an old picture from a frame๐ Watch for: how the dust cover is cut and how fasteners are pulledOpens on YouTube in a new tab
โถTaking a frame apart and putting it back together๐ Watch for: the order of layersOpens on YouTube in a new tab
โถPhotos stuck to picture frame glass๐ Watch for: what a stuck print looks like. We capture through the glass first.Opens on YouTube in a new tab
โถShooting framed artwork without glare๐ Watch for: where the two lights goOpens on YouTube in a new tab
โถRemoving reflections with polarization๐ Watch for: glare disappearing as the filter turnsOpens on YouTube in a new tab
โถCross-polarised light source๐ Watch for: polarizing film on the lightsOpens on YouTube in a new tab
โถPhotographing art with a copy stand๐ Watch for: squaring the camera to the artworkOpens on YouTube in a new tab๐ Worksheet 6: Framed photos
Part A: Quick check
Click one answer. Green means correct. Red means try again. You can try as many times as you need.
1. You open a frame and the photo is stuck to the glass. What is the first thing we do?
โ Capturing through the glass has zero risk and must exist before anything else is considered.
2. Why is a scan through frame glass often soft on the ET-2750?
โ CIS sensors have almost no depth of focus, so 2 mm of frame glass is enough to blur.
3. A photo is held to the mat by old masking tape. What do you do?
โ Peeling tape lifts the paper or image. We leave it and cut it free.
4. Where do lights go when photographing a framed photo?
โ At 45 degrees the reflection bounces away from the lens.
5. The glass in a frame is cracked. What do you put on before handling it?
โ Cracked glass can separate when the fasteners are released.
6. Which of these is a hinged-case image that we never open?
โ Cased images are sealed packages. Opening lets in air that tarnishes the plate.
7. Which online method for stuck photos do we never use?
โ Heat and moisture make gelatin stickier and destroy the image layer.
Part B: Hands-on practice
Do each task with real equipment and practice media. Tick it when you have done it. Your trainer signs when they have watched you do it.
| I did it | Task | Trainer initials |
|---|---|---|
| Photograph a practice frame front and back, then open it and bag every fastener. | ||
| Identify how the photo is attached in 4 different practice frames. | ||
| Cut a tape hinge free without peeling tape from the print. | ||
| Do the 2 mm corner test and say whether the photo is stuck. | ||
| Scan a glass-and-photo sandwich on the ET-2750 and judge its sharpness at 100%. | ||
| Set up two lights at 45 degrees and photograph a framed photo with no visible glare. | ||
| Reassemble a frame in the original layer order. |
Part C: Write or draw your answer
1. List the layers of a frame from front to back.
2. A client insists we "peel it off the glass". What do you say, and who do you get?